Services

Safe Hydraulics Training

• Introduction
• Safety
• Periodic Inspections & Replacement
• Hose Selection
• Hose Standards
• Coupling Selection
• Proper Hose Assembly
• Hose Cleanliness
• Hose Assembly Routing
• Installing Hose Assemblies
• Crimper Preventive Maintenance
• Troubleshooting
• Hose Risk Management
• Sentry ID Services
• Hose Accessories

Hydraulics Training Course

► Hydraulic principles of mechanical maintenance,
► Types of hydraulic fluids and their characteristics.
► Describes components of the hydraulic system and their functions for maintenance procedures, including filters and
     strainers, reservoirs and accumulators, pumps, piping, tubing and hoses, control valves, relief valves, and actuating devices.
► This hydraulics course offers a variety of cylinders and training on hydraulic motors.

Typical Pyplok Training Certificate

Lubetrend One Day Training Proactive Fluid Management

► About Canglobal
► Maintenance Costs
► How To Curb Of Increasing Maintenance Costs
► Maintenance Philosophies
► Machine Progression Towards Failure
► Case Studies
► Major Maintenance Cost-Reduction Opportunity
► Contamination Induced Wear
► Water Damage
► Fluid Contamination
► Typical Dynamic Clearances
► Fluid Purification Systems
► Proactive Fluid Management
► Why Monitor Contamination
► Filtration Facts
► Primary Causes Of Lubricant Related      Failures
► Proactive Fluid Solutions
► Strategy

Lubetrend One Day Training Oil Analysis Course

► Training Objectives and the role of oil analysis    
► Classification and Properties of oil
► Tests Performed and their Significance
► Tests Performed and their Significance (cont.)    
► Oil Cleanliness and Particle Analysis        
► Taking an Oil Sample
► Trouble Shooting and Predictive Maintenance    
► Establishing specific alert levels        
► Interpretation of results
► Case Studies             
► Choosing a laboratory            
► Review and Questions        
► Coolant and Fuel analysis or Lubetrend Web training

Courses

1. OVERVIEW OF OSHA AND ITS REGULATIONS 
2. Contractor Safety Management 
3. Safety & Health in Warehousing & Logistics 
4. Transforming an Effective Safety & Health Committee in The Workplace 
5. Chemical Safety & Spillage Response Procedures
6. Fire Safety & Fire Fighting Training Program
7. Hazard Identification, Risk Assessment and Risk Control Program (HIRARC)
8. Emergency Response Team Workshop
9. Manufacturing Safety
10. Chemical and Scheduled Waste Management 
11. Chemical Management
12. Setting Up a Safety Committee and Implementing OSHA
13. Waste Management and Handling Dangerous Goods
14. Occupational Safety and Health at Warehouse
15. Malaysian Environmental Laws Interpretation & Application
16. Safe Hydraulics Training
17. Typical Pyplok Training Certificate 
18. Lubetrend One Day Training Proactive Fluid Management 
19. Lubetrend One Day Training Oil Analysis Course

PERSONAL

Mr. Rasanayagam is a registered competent Safety and Health Officer Registration No.: JKKP IS 127/438/2/2071) with Department of Occupational Safety and Health (DOSH) since year 2001. He is a professional Safety and Health officer.

Re-Usable Element Cleaning

3 Stage Filter Inregrity Services

	Stage 1 – Inventory Data Base Contamination Patch Test
	Stage 2 – 1st Stage Cleaning 2nd Stage Cleaning 3rd Stage Cleaning
	Stage 3 – Cleanliness Patch Test Certificate of cleanliness

• Will be in a bypass mode if the housing is fitted with a bypass valve, allowing the contaminated oil to flow into the hydraulic system prematurely wearing out expensive hydraulic components.
• If the filter housing has no bypass valve and fitted with a high collapse filter then you may run the risk of the filter being damaged and releasing the contaminants from the filter which also allow contamination to enter the hydraulic system and prematurely wear out expensive components.

Do you purchase expensive reusable Filter elements? Canglobal can cut your costs, save you money and guarantee integrity of your filter elements by testing to ISO 4406-1999 standard. Canglobalsupply you the following services for your reusable filter elements;

Hydraulic Flushing Services And Equipment

High Pressure Testing

Canglobal offers pressure testing services for low and high pressure testing.

We can test with liquid, nitrogen, helium or air with a pressure range from a few psi to 30,000psi.

Our certification is for proof testing, leak testing of newly fabricated systems or systems that are in service.

Canglobal’ shydraulics and pneumatics testing is suited for applications in wide range of industries. We are constantly expanding our services.

Contact us with your needs for a customized pressure test program.

Offshore Platforms and Industrial Flushing Services

Newly fabricated systems or systems that are in-service.

Canglobal's flushing is designed as a part of the lifelong maintenance program, and preparations for newly fabricated systems should be included in the design phase.

Our flushing guidelines meet the following international standards, API, ASTM, ISO, etc.

Reduce costly shut downs or costly upgrade or a complete modification’s due to contamination build up.

It is more cost-efficient to perform periodic cleaning such as a proactive flushing service program.

Reduce costs, Save time and money, It is often possible to perform a flush while system is in operation.

Contact Canglobal and speak with our flushing expert to discuss how we can save you time and money.

Oil Recycling

Oil Life Extension, Recycling and Reclamation Services

Our claim, we turn schedule waste and dirty oil back into usable industrial lubricants that can be used in the same machine it was removed from, without releasing any greenhouse gases during the process. Our D.O.E registered facility and D.O.E Licensed lorry are authorized to collect the following Schedule Waste Codes: SW305 SW306 SW307 The various lubricants which fall under the above mentioned Schedule Waste codes are as follows: Air conditioning Lubricants Compressor Lubricants Gear Lubricants Hydraulic Lubricants Industrial Coolants Turbine Lubricants Please contact us for a free constellation visit to learn how we can save you and your company time and money! Click To Download Map

Department Of Environment (D.O.E) License

Chemical Flushing

Filtration / Oil / Environmental Chemical Flushing Service
Offshore Platforms , FPSO, Vessels, Cranes, Turbines, Well Control Panels, etc.
	Canglobal can achieve oil cleanliness levels: ISO 10/ 7/ 0 or well below NAS 0. Our technology can achieve unprecedented cleanliness. During the Commissioning or Maintenance phase to ensure that systems are clean before start-up. Pre filtration and flushing is a well proven and very effective cleaning method, oil and environmental chemicals can circulate though the system, by means of turbulent flow at a set target cleanliness and or temperature. During the circulation the oil and or Environmental Chemical or oil is filtered and particles and contamination removed. The final product will be a clean system according to the predetermined specifications of the specific equipment and or machinery. Our filtration and flushing services are monitored and documented through a laboratory calibrated onsite particle counter. This guarantees the customer reel time results.

Facility Commissioning
Before a facility can begin operation, any protective coatings, fabrication and installation debris or scales present are often removed. If this was not done either the efficiency of production would be lessened or the plant itself could be damaged. One example is the removal of rust and coatings from high pressure gas compressor suction pipework.
Environmental Chemical
Innovative and cost effective solutions are what we offer to our customers. With our Environmental Flushing Solution we are able to reduce chemical and schedule waste, ultimately reducing operational and project costs. Our standards focus on the environment and health and safety.

Services Online / Offline Filtration Oil Flushing Environmental Chemical Flushing Moisture Removal Particulate Removal

Application: Tubing Oil Flushing Pipes Pipe systems Umbilicals Heat Exchangers

Benefits: Trouble free start-up of systems Clean systems extend bearing lifespans Continuous operations

Deliverables: Clean and reliable piping systems Experienced personnel and fit for purpose equipment Particle and water content analyses by use of onsite laboratory equipment Documented process

Filtration Services

Our Filtration Services contribute to greater efficiency and profitability of your business. Our Services, consist of utilizing the latest filtration technology in the market. With our products and techniques we are able to achieve unprecedented cleanliness of your lubricants and internal components even while your machines are operational.
Achieve Oil cleanliness levels: ISO 10/ 7/ 0 or well below NAS 0
	Our filtration systems have the unique ability to remove particulate of ANY size, right down to sub micron sized particulate. Our filtration systems will operate with any semi-conductive or non-conductive fluid, lubricant, or oil, within broad temperature and viscosity limits. Our systems ability to remove the pre-cursors of oxidation by-products, will prevent, and over time, remove existing tar and Varnish deposits. Reduce down time, equipment life extension, fluid life extension.

PROBLEM: Water H2O and Particulate Contamination
There has always been a problem with condensation in the bulk storage of fuels and oils. Water and particulates have found ways to enter even through the tightest sealed tanks. The water condenses from humid air trapped inside the tank, but it also can enter through bad seals, vents and breathers. Traditionally removing this water or moisture has been a problem.  Many costly measures have been used to try and solve this problem. No matter how water enters your tanks, it will find its way into your equipment.  When water ends up in your engine, hydraulic system or machinery it will cause costly damage. In order to eliminate water from your hydrocarbon streams in an effective and efficient way, it would be necessary to utilize one of CanGlobal’s many portable and stationary filtering systems. This technology allows you to combine water and particulate filtration into one simple step.   Contact us today for further information of our technology and services.

Stop Throwing Your Oil Away!

Our Filtration Services contribute to greater efficiency and profitability of your business. Our  Services, consist of utilizing the latest filtration technology in the market. With our products and techniques we are able to achieve unprecedented cleanliness of your lubricants and internal components even while your machines are operational. Achieve Oil cleanliness levels: ISO 10/ 7/ 0 or well below NAS 0 Our filtration systems have the unique ability to remove particulate of ANY size, right down to sub micron sized particulate. Our filtration systems will operate with any semi-conductive or non-conductive fluid, lubricant, or oil, within broad temperature and viscosity limits. Our systems ability to remove the pre-cursors of oxidation by-products, will prevent, and over time, remove existing tar and Varnish deposits. Reduce down time, equipment life extension, fluid life extension. PROBLEM: Water H2O and Particulate Contamination    There has always been a problem with condensation in the bulk storage of fuels and oils. Water and particulates have found ways to enter even through the tightest sealed tanks. The water condenses from humid air trapped inside the tank, but it also can enter through bad seals, vents and breathers. Traditionally removing this water or moisture has been a problem.  Many costly measures have been used to try and solve this problem. No matter how water enters your tanks, it will find its way into your equipment.  When water ends up in your engine, hydraulic system or machinery it will cause costly damage. In order to eliminate water from your hydrocarbon streams in an effective and efficient way, it would be necessary to utilize one of CanGlobal’s many portable and stationary filtering systems. This technology allows you to combine water and particulate filtration into one simple step.   Contact us today for further information of our technology and services.

Mobile Filtration Services

CANGLOBAL Mobile Laboratory and Mobile Filtration Services contribute to greater efficiency and profitability for your business. Stop replacing your lubricants on a operational time schedule and change to a Proactive Maintenance Schedule. Canglobal can reduce Scheduled Waste Services and costly down time while extending oil change intervals 3-5 times and reduce maintenance costs up to 70-80%.
Mobile Laboratory Services
Offer onsite Moisture, Particle Count and viscosity testing providing real time analysis and diagnosis of your lubricants.
Offline Filtration Services
Our Mobile off-line filtration service can filter single or multiple drums, IBC or Skid tank. Filtering your used lubricants cleaner than new oil.
Online Filtration
Achieve Oil cleanliness levels: ISO 10/ 7/ 0 or well below NAS 0.Our on-line filtration systems have the unique ability to remove particulate of ANY size, right down to sub micron sized particulate. Our filtration systems will operate with any semi-conductive or non-conductive fluid, lubricant, or oil, within broad temperature and viscosity limits. Our systems ability to remove the pre-cursors of oxidation by-products, will prevent, and over time, remove existing tar and Varnish deposits. Reduce down time, equipment life extension, fluid life extension.

Tank Cleaning Services

CANGLOBAL Mobile Laboratory and Mobile Filtration Services contribute to greater efficiency and profitability for your business. Stop replacing your lubricants on a operational time schedule and change to a Proactive Maintenance Schedule. Canglobal can reduce Scheduled Waste Services and costly down time while extending oil change intervals 3-5 times and reduce maintenance costs up to 70-80%
Contamination Build Up
THE PROBLEM: Water H2O and Particulate Contamination There has always been a problem with condensation in the bulk storage of fuels and oils. Water and particulates have found ways to enter even through the tightest sealed tanks. The water condenses from humid air trapped inside the tank, but it also can enter through bad seals, vents and breathers. Traditionally removing this water or moisture has been a problem. Many costly measures have been used to try and solve this problem. No matter how water enters your tanks, it will find its way into your equipment. When water ends up in your engine, hydraulic system or machinery it will cause costly damage.  In order to eliminate water from your hydrocarbon streams in an effective and efficient way, it would be necessary to utilize one of CanGlobal’s many portable and stationary filtering systems. These systems are accompanied with the cartridge and spin on style filters. These filters will remove water as well as particulate from your hydrocarbon streams. Free moisture as well as emulsified is absorbed into the filter media. This technology allows you to combine water and particulate filtration into one simple step.   Contact us today for a presentation of our technology.

Our Tank Cleaning Services, consist of utilizing the latest pneumatic vacuum technology.
Our high pressure blasting process is superior to the conventional sand blasting. Without the dust, sand residue and costly clean up.
With our products and techniques we are able to achieve unprecedented cleanliness of internal reservoirs and tanks.
Achieve Oil cleanliness levels: ISO 10/ 7/ 0 or well below NAS 0

CONTAMINATION BUILD UP

THE PROBLEM: Water H2O and Particulate Contamination
 
There has always been a problem with condensation in the bulk storage of fuels and oils.
Water and particulates have found ways to enter even through the tightest sealed tanks.
The water condenses from humid air trapped inside the tank, but it also can enter through bad seals, vents and breathers.
Traditionally removing this water or moisture has been a problem. 
Many costly measures have been used to try and solve this problem.
No matter how water enters your tanks, it will find its way into your equipment. 
When water ends up in your engine, hydraulic system or
machinery it will cause costly damage.

 In order to eliminate water from your hydrocarbon streams in an effective and efficient way, it would be necessary to utilize one of CanGlobal’s many portable and stationary filtering systems.
These systems are accompanied with the cartridge and spin on style filters. These filters will remove water as well as particulate from your hydrocarbon streams. Free moisture as well as
emulsified is absorbed into the filter media.
This technology allows you to combine water and particulate filtration into one simple step.  

Contact us today for a presentation of our technology.

Laboratory Services